Skip to product information
1 of 7

Momijiyama Tomae Daitsuki #453085md

Momijiyama Tomae Daitsuki #453085md

Regular price $165.00 USD
Regular price Sale price $165.00 USD
Sale Sold out
Shipping calculated at checkout.

Free U.S. shipping on orders over $500

GOVX ID Military & First Responders get a 10% discount! Click to verify.

dimensions

150mm x 82mm x 12mm (with Daitsuki 42mm)
Weight: 577g

Identification & Origin
Mine: Momijiyama  - "Autumn Leaf Mountain"), a closed western Kyoto / Tanba district mine located near the Kozaki mining area.
Strata / Layer: Tomae 
Format: Daitsuki  mounted directly onto a carved wooden base (dai) with a retailer/distributor mark stamped on the wooden flank (響 / Hibiki brand mark).
Dimntions: 150 mm × 82 mm × 12 mm; 577 g (stone plus wooden dai).


Stone Classification & Characteristics
Type: Awasedo / Shiage-toishi — fine natural finishing whetstone.
Coloration & Visual Pattern:
Primary body is an earthy gray-olive/greenish-ash (Asagi / Namito tone).
Prominent ochre-yellow skin/inclusion pattern (Kawa / light Nashiji / Kiita bordering) flaring down the left flank.
A distinct reddish cinnabar/iron oxide accent (Yake / Momiji flush) resting just off-center on the working surface.
Estimated Hardness: Approximately Level 3.5  (medium). Momijiyama stones from the Tomae layer typically possess a velvety, responsive draw with moderate self-slurrying capacity rather than the extreme glassiness of eastern razor stones.
Estimated Fineness / Grit Equivalent: #6,000 to #8,000 JIS equivalent.
Best Uses: Kitchen knives (particularly wide bevels where it creates a clean, semi-cloudy kasumi contrast), gouges, chisels, and general edge-refinement before an ultra-fine strop or razor finisher.

Evaluation & Working Quality
Wide Working Surface: At 82 mm wide, it provides ample transverse real estate for wide kitchen knives and broad carpenter tools despite the compact 150 mm length.
Tactile Feedback: provides excellent tactile "bite" and feedback, reducing stone loading while producing smooth edges without excessive scratching.
Base Stability: The factory-cut wooden dai gives rigidity and protection to the 12 mm stone slab, which prevents cracking under sharpening pressure.

Flaws & Condition
Shallow Stone Thickness: At 12 mm nominal thickness, the stone has a modest consumable depth, which is standard for pre-mounted daitsuki plates of this footprint but limits multi-decade high-volume workshop usage.
Perimeter Layering & Edge Chips: Slight micro-chipping and minor natural delamination lines visible along the raw stone bevels where it interfaces with the wooden base.
Natural Mineral Variation: The reddish Yake flash and yellow skin boundary on the working face are benign.

care instructions

1. Preparation & Water Management
Splash-and-Go Only: Never soak your natural finishing stone in a water bath. Prolonged submersion softens the natural binders and risks cracking or delamination along natural mineral lines.
Surface Wetting: Mist or splash clean water onto the working face just before sharpening. Add water sparingly throughout your session to maintain a slick working surface.
Bench Placement: Place the stone on a non-slip rubber base or a dedicated wooden stone holder with gentle clamping pressure.
2. Slurry Generation & Sharpening
Soft to Medium Stones (Hardness 2.5–3.5): These stones naturally release their own slurry under light blade pressure. Let the auto-generated mud do the work; do not wash it away mid-session.
b Use a diamond plate (such as an Atoma 1200), a clean Tomo Nagura, or a Mikawa Nagura to raise a thin, milky slurry in 5 to 10 light circular passes before laying your blade flat.
Pressure & Technique: Maintain light, even pressure. Allow the semi-rounded silica particles in the slurry to break down naturally—this self-refining action creates the signature toothy edge and cloudy kasumi finish.
Slurry Thickness: If the mud becomes too sticky or pasty, add a few drops of water. If it is too thin, work the stone lightly to concentrate the abrasive particles.
3. Cleaning, Drying & Long-Term Care
Rinse Clean: When finished, gently rinse off steel swarf and residual slurry using room-temperature tap water. Do not use dish soap, detergents, or hot water.
Air Dry Indirectly: Wipe the stone dry with a clean towel and allow it to dry completely at room temperature, away from direct sunlight, heating vents, fans, or freeze-thaw cycles.
Storage: Store the completely dry stone flat on a shelf in a climate-controlled room. Avoid enclosing a damp stone in an airtight plastic box.
Edge Lapping: Keep the working surface flat by lightly dressing it with a fine diamond plate (Atoma 1200 or 400) under running water when dish patterns begin to form. Chamfer the outer top perimeter edges lightly to prevent edge chipping during blade passes.

View full details